Tools ES

22 Results

2025-03-29 15:21:06

Hitachi C12 FDH 12" Compound Miter Saw

Hitachi C12 FISH 12" Dual Compound Miter Saw. Laser feature doesn't work. Missing the included wrench for changing the blade. Good saw with lots of abilities.

Tools - Devils Lake, ND

2025-03-29 15:10:21

1 1/2 hp Craftsman router mounted on a table.

1 1/2 hp Craftsman router mounted on a router table, extra router bits. Tested and works as should.

Tools - Devils Lake, ND

2025-03-23 14:59:50

80-gallon air compressor tank

Sanborn Magna Force Use as extra air storage Motor going bad pump parts obsolete

Tools - Langdon, ND

2025-03-23 10:41:58

I have a 12 foot tennsmith sheet metal break great for bending metal or any sort o

f things for whatever you want! I just dont use it as my dad passed away and I have no use for it

Tools - Devils Lake, ND

2025-03-22 09:58:00

Yamaha ef3000is inverter generator. Like new (never even tried to start it)

. I bought it and decided to get a bigger generator, so I never used it. These are extremely quiet and fuel efficient to

Tools - Cando, ND

2025-03-21 13:59:16

New assortment of clevis's and double hook chains. Please see pictures for sizes

and amount. Located @ binford nd All to go $1000.

Tools - Binford, ND

2025-03-18 21:08:18

Landa hot water pressure washer

Mechanics special, diesel heater. Pumps water but low pressure. Hot water heater runs but doesn’t heat. 110 volt. Don’t want to take the time to fix.

Tools - Crary, ND

2025-03-15 10:45:56

Weather guard pack rat storage boxes

Tools - Devils Lake, ND

2025-03-09 07:33:40

6500 powermate generator. Was modified to fit in camper. Worked great just too noi

sy. All framework is basically gone. Hour meter shows 4 hours. I have the gas tank, muffler, recoil start etc.

Tools - Sheyenne, ND

2025-03-08 16:02:46

For sale 2 Lincoln 12 volt grease guns . Both work good. Changed to dewalt cause a

ll my other tools are dewalt.

Tools - Adams, ND

2025-03-05 16:10:00

Stationary Aaladin Pressure Washer

Stationary Aaladin Pressure Washer Single phase 8 hp motor Specs in picture 310 hrs. Call for more info

Tools - Osnabrock, ND

2025-03-04 11:36:40

For sale Onan generator Emerald 3. Had it running but would not generate power. Se

lling for parts.

Tools - Sheyenne, ND

2025-01-28 00:26:00

Miller 3ph Wire feed welder

Tools - Adams, ND

2024-10-12 09:41:06

pinch bar, Atlas

Tools - Leeds, ND

2024-10-03 21:32:10

Irwin parallel clamps2-48" and 2- 24" hardly used and comes with a wall hanger

Tools - Devils Lake, ND

2024-09-20 10:19:35

Tri fold metal divider.

Tri fold metal. Each panel is 30 inches wide by 49 inches tall. Open, all three panels, in line, 91 wide by 49 tall. Use as "fun with magnet" board, science fair display, welding/grinding

Tools - New Rockford, ND

$5

2024-09-20 09:33:37

Brazing rod holder.

36 inch gas welding rods and brazing rods fit this stand. Take a look. Make an offer. Located in New Rockford ND.

Tools - New Rockford, ND

2024-09-20 00:55:16

Clipped head smooth nails 3 1/4 by 0.131. About 60 clips of 40 nails per clip.

About 2,400 individual nails. Great condition. No rust ot broken clips. Take a look. Make an offer. Located in New

Tools - New Rockford, ND

2024-09-12 00:15:08

Rinkon 50-122. 48" sander with 10" disc sanderHardly used, comes with new belts o

f various grits

Tools - Devils Lake, ND

2024-05-06 00:15:01

Tow rope. 2 1/4 inch diameter by 20 feet. Eyelets both ends.

Always stored indoors. Never wet. Used twice as a two rope. Very nice used condition. Located in New Rockford ND. Take a look.

Tools - New Rockford, ND

2023-11-14 15:58:42

Craftsman Drill/Drivers and Impact Driver Set - 19.2V

Craftsman Drill/Drivers and Impact Driver - 19.2V 1 - 3/8" drill/driver CS1011 2 - 1/2" drill/driver CS1251 1 - 1/4" hex shaft impact driver CS1011 2 chargers CS1107,CS1251 5 nickel-cadmium

Tools - Langdon, ND

2023-10-18 08:29:55

Viper 14 inch abrasive blades. $500 per box of 25. 2 boxes available

Tools - Langdon, ND

View All Tools listings in Air Compressor, Anvils or Automotive

22 Ads | Page 1 of 1 | Jump to Page:

Advertise With Us

NorthWing Media

Rules & Policies